Minuteman 320 SE Manuals:
1. How do I "home" the bar feeder (also referred to as "resetting the zero point")?
Edge Tech Minuteman 320: Begin with the guide channel closed and the bar pusher about a foot forward from the rearmost position from the lathe. Press and hold the "Pre Auto" button (top right button) on the remote control. After approximately 10 seconds the bar pusher will begin to move to the rear toward the home position micro-switch. Release the button as soon as the pusher begins to move rearward.
2. How do I shorten my remnant length?
Edge Tech Minuteman 320: The remnant length is controlled by the parameters "Maximum Pusher Forward Travel" and "Part Length + Cutoff Tool Width", the distance from the chuck or guide bushing the cut-off occurs and the length of the material in the guide channel. The front limit position is the farthest the bar pusher can travel forward into the lathe. The part length is the sum of the overall part length, the width of the cut-off tool and the amount of material left for facing. When the pusher doesn't have enough travel left to move the distance in the part length parameter before reaching the front limit position the End of Bar signal is sent. If the remnant is too long verify the front limit position parameter and the part length parameter. Keep in mind that on all lathes there will be a certain amount of unusable material. This unusable length can be measured by moving the bar pusher as far as possible into the lathe and and measuring from the cut-off tool to the inside of the bar feeder collet stop. For Swiss type lathes move the headstock to the cut-off position and measure from the back of the cut-off tool to the stop inside the bar feeder collet. This measurement is your minimum remnant length. The remnant length can be up to one part length longer than the minimum depending on home much material is remaining.
3. How do I set my "end of bar" (referred to as "front limit position" on FMB and "max end of bar" on Edge products)?
Edge Tech Minuteman 320: Before beginning reference (re-zero) the bar pusher. For sliding headstock machines only, move the headstock into overtravel toward the guide bushing. For all machines, move the bar pusher with a collet attached, no material in the channel, forward until the bar pusher collet contacts the lathe collet. Smaller diameter bar pushers may travel inside the lathe collet, larger diameter bar pushers may stop sooner at the back of the collet or at the collet sleeve. Record the position of the bar pusher from the bar feeder screen. Enter the position minus 3mm (1/8 inch) in the Maximum Pusher Forward Travel parameter in the F2 Fixed Parameter section. Please note that if the guide channel size is changed the bar pusher of the new channel may have a different stopping point in the spindle than the bar pusher originally used to set up the machine.
4. How do I set the "top cut" position (first insert position / facing length)?
Edge Tech Minuteman 320: The facing position controls where the new bar stops in the lathe during a bar change. The value of the parameter is a measurement of the distance from the facing flag to the face of the guide bushing minus 2 inches for Swiss type lathes. For fixed headstock lathes measure the distance from the facing flag to the face of the collet. Enter the measurement in the Facing Position parameter in the F2 Fixed Parameter section. To get to this parameter press the F2 button and enter the password 258. The screen will change to show the Facing Position parameter. Type the new value and press enter (F9 key to the right of the 0 key). Press the F3 key to return to the main screen.
5. How do I prevent the pusher-collet assembly from disengaging with bar stock in a sliding headstock (Swiss) lathe?
Edge Tech Minuteman 320: The most common cause for losing the bar from the pusher collet is the lack of a dwell or too small a dwell in the part program after the lathe collet opens and after the lathe collet closes. The dwell is required to allow time for the signal from the lathe to reach the bar feeder and for the bar feeder to act on the signal. Looseness in the linkage of the sync device, a worn rotating tip, obstructions to the bar pusher in the channel or nose and slack in the synchronization belt or drive belt can also contribute to losing the stock from the pusher collet. The synchronization device can be checked by loading a bar into the lathe collet as normal. With the bar feeder in manual and the lathe collet open, disconnect the synchronization bar from the lathe and push the bar toward the bar feeder to make a gap. Close the lathe collet to engage the synchronization. Pull the synchronization bar toward the lathe. If the synchronization device is working properly you will not be able to move the sync bar toward the lathe. Do not push the sync bar toward the bar feeder. If the synchronization is working this will pull the bar pusher collet off the material.
6. What parameters or settings do I have to change when setting up a new job?
Edge Tech Minuteman 320: When changing to a new job the Part Length + Cutoff Tool Width parameter in the F1 User parameters should be changed. The proper setting is the sum of the overall part length + the width of the cut-off tool + any facing stock used. This dimension reflects the total amount of material required to make and cut off one part. The facing length may need to be altered in case of a left handed cutoff tool or to provide a longer "stick-out" of material on the bar reload. This can be accomplished through the Facing Position parameter located in the F2 fixed parameters. The parameter can be adjusted higher or lower as needed. This parameter requires a password, 258, to gain access. The Open Collet Speed and Open Collet Torque parameters normally are not changed but can adjusted in special cases such as extremely small or large diameters or flexible material. These parameters can be found in the F1 User parameters.
7. Explain the dwells I need to have present in my lathe program to accommodate the bar feeder?
Edge Tech Minuteman 320: We recommend a ½ second dwell in the main part program after the collet opens and after the collet closes for Swiss type lathe applications to allow the signal for the lathe collet open to reach the bar feeder and be processed. This allows the synchronization device time to release at the collet open signal and to reengage at the closed collet signal. For fixed headstock lathes a dwell is required in the part program to give the bar feeder time to advance the material for the next part before the collet closes. The length of dwell is dependent on the length of the part to be feed out.
8. How do you set the chain/belt tension on my bar feeder?
Edge Tech Minuteman 320: On newer model Minuteman bar feeders the belt adjustment is made by loosening the two bolts in the slots on top of the beam near the rear plate of the bar feeder. With the screws loose, pull the motor toward the rear plate to tighten the drive belt, the tighten the adjusting bolts. Older Minuteman bar feeders were chain drive and use an idler sprocket for adjusting the chain. Moving the idler to the rear causes the chain to tighten.
9. How do I adjust the steady rest rollers for different stock diameters?
Edge Tech Minuteman 320: To adjust the rollers load a bar into the lathe and close the collet. Push the Pre-Auto button (pendant control, top right button) to close the roller steady. The long cap screw with a sleeve and jam nut is used to adjust the rollers. Turn the screw counterclockwise until no tension is felt on the screw. Press the manual button (pendant control, top center button), then the pre auto button again to make sure the rollers are closed on the bar. Rotate the adjusting screw clockwise until tension is felt, then rotate the screw clockwise another 1/4 turn. Tighten the jam nut. Press manual to release the rollers. This procedure applies to both the 1st anti-vibration and the MAVD rollers.