Rebel Videos

Return to Edge-U-Cation
Return to Edge-U-Cation

Rebel 102 Spindle Liner Change

In this video, we show why the Edge Rebel Series loaders are the best solution for frequent changeover work!

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Brian Grisez describes bar loader positioning relative to a lathe.

Edge Technologies Rebel 80 v3 Calibration

This is a video instruction for calibrating the separation fingers and v-tray position on Edge Technologies new Rebel 80 V3 Loader.

Why Is My Bar Not Reading on My Rebel Short Loader?

This video troubleshoots all the reasons a bar might not read on a Rebel short loader.

Edge Rebel V65 Eco Critical Parameter Settings

Video walkthrough of setting critical parameters on Edge Rebel V65 Eco machine and description of symptoms if these are set incorrrectly.

Edge Rebel 80/102 Separator Finger Calibration Procedure

This video documents the procedure for the software calibration of the separation fingers for the Edge Rebel 80/102.

Rebel 102 Spindle Liner Change

In this video, we show why the Edge Rebel Series loaders are the best solution for frequent changeover work!

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Brian Grisez describes bar loader positioning relative to a lathe.

Edge Technologies Rebel 80 v3 Calibration

This is a video instruction for calibrating the separation fingers and v-tray position on Edge Technologies new Rebel 80 V3 Loader.

Rebel 102 Spindle Liner Change

In this video, we show why the Edge Rebel Series loaders are the best solution for frequent changeover work!

Why Is My Bar Not Reading on My Rebel Short Loader?

This video troubleshoots all the reasons a bar might not read on a Rebel short loader.

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Brian Grisez describes bar loader positioning relative to a lathe.

Edge Rebel V65 Eco Critical Parameter Settings

Video walkthrough of setting critical parameters on Edge Rebel V65 Eco machine and description of symptoms if these are set incorrrectly.

Edge Technologies Rebel 80 v3 Calibration

This is a video instruction for calibrating the separation fingers and v-tray position on Edge Technologies new Rebel 80 V3 Loader.

Edge Rebel 80/102 Separator Finger Calibration Procedure

This video documents the procedure for the software calibration of the separation fingers for the Edge Rebel 80/102.

Other Helpful Sources

Bar Lift

The bar lift can be used for extended capacity or as an aid for lifting heavy bar stock, up to 80 mm. Many customers will roll bars off a forklift and never have to...

Why Is My Remnant So Long

Are you asking this question: Why is my remnant so long, specifically related to bar feeder remnants in Swiss- or sliding headstock applications. In this instructional...
A bundle loader at a customer site

Bundle Loader

The bundle loader is the largest step you can take in fully automating your bar feeder. It can hold up to 5,000 lbs of stock and is usually loaded with an entire bundle...

Testing Three Phase Pump Rotation

In this video, Regional Service Manager Brian Grisez demonstrates how to test the rotation direction of a three phase pump in a bar feeder using a zip...

Bar Loader Install, Positioning Instruction

In this video, Brian Grisez describes how to successfully calculate the installation position for a bar loader relative to a lathe, and all the variables and...

Vortex Mist Collectors

[dvg_divi_video_gallery columns="1" _builder_version="4.27.0" _module_preset="default" global_colors_info="{}"][dvg_divi_video_gallery_item...

Why Is My Remnant So Long? Part 2

Part 2 of an instructional video series describing remnant length related to bar fed Swiss machine applications. If you haven't watched Part 1, start with that....

Why Is My Bar Not Reading on My Rebel Short Loader?

Transcript for Why Is My Bar Not Reading on My Rebel Short Loader: Welcome to Edge Technologies. My name is Kyle. I'll be walking you through how to inspect and replace...

How to Correctly Test Bar Straightness

[dvg_divi_video_gallery columns="1" _builder_version="4.27.4" _module_preset="default" global_colors_info="{}"][dvg_divi_video_gallery_item title="How to Correctly Test...

Edge Rebel 80/102 Separator Finger Calibration Procedure

In this video, Regional Service Manager Brian Grisez documents the procedure for the software calibration of the separation fingers for the Edge Rebel 80 or Rebel 102....