Rebel Videos

Return to Edge-U-Cation
Return to Edge-U-Cation

Rebel 102 Spindle Liner Change

In this video, we show why the Edge Rebel Series loaders are the best solution for frequent changeover work!

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Brian Grisez describes bar loader positioning relative to a lathe.

Edge Technologies Rebel 80 v3 Calibration

This is a video instruction for calibrating the separation fingers and v-tray position on Edge Technologies new Rebel 80 V3 Loader.

Why Is My Bar Not Reading on My Rebel Short Loader?

This video troubleshoots all the reasons a bar might not read on a Rebel short loader.

Edge Rebel V65 Eco Critical Parameter Settings

Video walkthrough of setting critical parameters on Edge Rebel V65 Eco machine and description of symptoms if these are set incorrrectly.

Edge Rebel 80/102 Separator Finger Calibration Procedure

This video documents the procedure for the software calibration of the separation fingers for the Edge Rebel 80/102.

Rebel 102 Spindle Liner Change

In this video, we show why the Edge Rebel Series loaders are the best solution for frequent changeover work!

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Brian Grisez describes bar loader positioning relative to a lathe.

Edge Technologies Rebel 80 v3 Calibration

This is a video instruction for calibrating the separation fingers and v-tray position on Edge Technologies new Rebel 80 V3 Loader.

Rebel 102 Spindle Liner Change

In this video, we show why the Edge Rebel Series loaders are the best solution for frequent changeover work!

Why Is My Bar Not Reading on My Rebel Short Loader?

This video troubleshoots all the reasons a bar might not read on a Rebel short loader.

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Brian Grisez describes bar loader positioning relative to a lathe.

Edge Rebel V65 Eco Critical Parameter Settings

Video walkthrough of setting critical parameters on Edge Rebel V65 Eco machine and description of symptoms if these are set incorrrectly.

Edge Technologies Rebel 80 v3 Calibration

This is a video instruction for calibrating the separation fingers and v-tray position on Edge Technologies new Rebel 80 V3 Loader.

Edge Rebel 80/102 Separator Finger Calibration Procedure

This video documents the procedure for the software calibration of the separation fingers for the Edge Rebel 80/102.

Other Helpful Sources

How to Set Front Limit Position and First Insert Position on Edge/FMB Bar Loaders

In this instructional video, Regional Service Manager Brian Grisez documents the process for setting Front Limit Posiotion and First Insert Position on Edge and FMB bar...

Testing Synchronization Device on Bar Loader

In this video, Regional Service Manager Brian Grisez demonstrates how to test a synchronization device on a bar loader used in Swiss-type or sliding headstock...

Vortex Mist Collectors

[dvg_divi_video_gallery columns="1" _builder_version="4.27.0" _module_preset="default" global_colors_info="{}"][dvg_divi_video_gallery_item...

Edge Rebel V65 Eco Critical Parameter Settings

In this video, Regional Service Manager Brian Grisez walks through how to set two critical parameters on an Edge Rebel V65 Eco machine. He also describes the symptoms...

Edge Technologies Rebel 80 v3 Pusher Removal

In this video, Regional Service Manager Brian Grisez goes over some of the circumstances in which you might need to remove the pusher from an Edge Technologies Rebel 80...

Rebel 102 Spindle Liner Change

"I would love to add a barfeeder to my lathe, but I machine so many different stock diameters. I can't dedicate all day to set-up..." The Edge Rebel Series loaders make...

Bar Lift

The bar lift can be used for extended capacity or as an aid for lifting heavy bar stock, up to 80 mm. Many customers will roll bars off a forklift and never have to...

Why Is My Remnant So Long? Part 4

This is part 4 in my ongoing series of videos describing the remnant length of bar fed machining applications. In this video we look at fixed headstock lathes and talk...

Why Is My Remnant So Long

Are you asking this question: Why is my remnant so long, specifically related to bar feeder remnants in Swiss- or sliding headstock applications. In this instructional...

Vortex Installation and Operation

Transcript of Vortex Installation and Operation: Hello, welcome to Edge Technologies. My name is Jason Bell, regional service manager of the West Coast, and I'm here...